Vermont Casting ST208 Manuale Utente Scaricare il pdf

Fuel Conversion Kit

Instructions

for Intrepid Direct Vent Gas

Stove

Kits:

Natural to LP: 20012921

LP to Natural: 20012910

WARNING!

The installation of this conversion kit must only

be undertaken by a qualiﬁed gas appliance

installer.

This kit is designed for conversion of the Intrepid Direct

Vent Gas Stove Models INDVR Series.

Tools required: 5/32” (4 mm) Allen wrench, 3/8” and

1/2” open end wrenches, needlenose pliers.

Kit contents: Pilot oriﬁce, injector oriﬁce, conversion

label.

Conversion Precautions

Allow unit to cool completely before beginning conver-

sion. Before proceeding, turn control knob on valve to

OFF and turn gas supply to OFF. Turn OFF any electric-

ity that may be going to the appliance.

Conversion Procedure

1. Remove stove front. Lift stove front up and then

swing bottom out and away to disengage from the

stove body. (Fig. 1)

2. Undo the right and left latches at the top of the glass

frame. (Fig. 2)

3. Pull the top edge of the glass and frame assembly

away from the ﬁrebox face. Place the assembly out

of the way on a ﬂat, padded surface such as a coun-

ter protected by a towel.

4. Remove the logset from the ﬁrebox.

ST967

Intrepid install front

7/07

INTREPID

ST967

Fig. 1 Remove the stove front. (Top vent shown)

ST208

glass swivel latch

12/99

ST208

Fig. 2 Release the latches to remove the glass frame.

Valve Conversion

1. Turn control knob to the OFF position, and shut off

the gas supply to the valve.

2. Allow the valve to cool to room temperature.

3. Remove the black protection cap by hand. (Fig. 3)

4. Insert a 5/32” or 4 mm Allen wrench into the hexago

nal key-way of the screw (Fig. 4), rotate it counter-

clockwise until it is free and extract it.















Figure 3















Figure 4

20012973 7/07 Rev. 0

1 2 3 4 5 6 7 8

Sommario

Pagina 1 - Fuel Conversion Kit

Fuel Conversion KitInstructionsfor Intrepid Direct Vent Gas StoveKits:Natural to LP: 20012921LP to Natural: 20012910WARNING!The installation of this

Pagina 2 - 1/28/00 djt

2200129735. Check that the screw is clean and if necessary re-move dirt.6. Flip the screw. (Fig. 5)7. Using the Allen wrench as shown in Figure 6,

Pagina 3 - 6/07 djt

320012973 • Remove pilot oriﬁce with needlenose pliers. (Fig. 12) NOTE: Use a wrench to hold pilot tube in place while removing the oriﬁce. • Instal

Pagina 4 - 

4200129733. Reinstall logs.a. Install the rear log by mating the notch on the bot-tom of the log with the raised notch on the back left side of the

Pagina 5 - Figure 18

520012973Left LogRight LogFigure 18LG494Rear LogTop LogLeft LogRight LogEmber BedLG495Figure 19

Pagina 6

620012973Table 2. Injector Oriﬁce Size MatrixConversion to LP Input (BTU/h) Kit # Oriﬁce Part # Minimum Maximum 20012921 #56 (.0465”)

Pagina 7

720012973

Pagina 8 - CFM Corporation

820012973410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 800-668-5323 • www.cfmcorp.comCFM Corporation

Commenti su questo manuale

Nessun commento

Vermont Casting ST208 Manuale Utente

Navigare online o scaricare Manuale Utente per Stufe Vermont Casting ST208. Vermont Casting ST208 User's Manual Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi Stufe Vermont Casting ST208